02-08-2018, 06:06 AM | #67 |
Major General
2376
Rep 8,364
Posts |
|
Appreciate
0
|
02-08-2018, 08:51 AM | #69 | |
Private
3
Rep 53
Posts |
Quote:
|
|
Appreciate
0
|
02-08-2018, 09:10 AM | #71 | |
Second Lieutenant
70
Rep 284
Posts |
Quote:
Not even looked at updating e-sys - I've got an old Token solution. Will this still work or will I need to update? I know i'll need the new psdzdata - but they seem pretty easy to get. |
|
Appreciate
0
|
02-08-2018, 11:14 AM | #73 |
Major General
2376
Rep 8,364
Posts |
VO coding does not require Token. But, if you you are doing FDL coding, you will need to upload launcher to 2.8.
|
Appreciate
0
|
02-08-2018, 02:58 PM | #75 | |
Second Lieutenant
186
Rep 235
Posts |
Quote:
Bimmercode is still a bit limited on G30, so e-Sys may be a better option depending on what you're looking to code. One major plus of bimmercode for some is VIM at any speed, I believe e-sys can only do it up to a certain speed. |
|
Appreciate
0
|
02-09-2018, 04:04 AM | #76 |
Second Lieutenant
70
Rep 284
Posts |
I think I will go for both actually - going to try Bimmercode as its only £25 and will setup e-sys because i've used it before.
E-sys is fine to use, just takes awhile to ensure everything is setup correctly. |
Appreciate
0
|
02-09-2018, 09:26 PM | #77 |
Major General
2376
Rep 8,364
Posts |
Bimmercode is good for VIM. Otherwise, you will want E-sys for a G-series.
|
Appreciate
0
|
02-12-2018, 10:43 AM | #79 |
Lieutenant
187
Rep 402
Posts |
Very easy just code the Alpina Display back to 'not active', as original.
__________________
|
Appreciate
0
|
02-12-2018, 11:14 AM | #81 |
Lieutenant
187
Rep 402
Posts |
Yes it displays up to 200mph. I presume the speed is correct. See if you can reach 200mph
__________________
|
Appreciate
0
|
02-12-2018, 11:18 AM | #82 |
Second Lieutenant
186
Rep 235
Posts |
|
Appreciate
0
|
02-13-2018, 03:54 AM | #85 |
Private
22
Rep 77
Posts |
That's unusually accurate, 10% optimistic seems to have been the norm for decades. Need to remember that when it comes to setting cruise control.
|
Appreciate
0
|
02-13-2018, 06:11 AM | #86 |
Second Lieutenant
186
Rep 235
Posts |
|
Appreciate
0
|
02-13-2018, 07:24 AM | #87 |
Private
22
Rep 77
Posts |
Interesting, I'm pretty sure I'm 10% over in my F10 and can't remember the last time I was in a car that didn't read over by around that amount. I just figured there were too many advantages to being on the optimistic side and that it was an accepted practice. Thanks for the confirmation.
|
Appreciate
0
|
02-13-2018, 07:34 AM | #88 | |
Second Lieutenant
186
Rep 235
Posts |
Quote:
A proper dial will be less accurate than digital readout and may well be 10% over. I was talking about the digital readout. |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|