12-10-2017, 03:31 PM | #23 |
Major General
2374
Rep 8,364
Posts |
Which version of E-sys and Launcher are you using? If premium, which chassis are you selecting and which E-sys connection target?
|
Appreciate
0
|
12-10-2017, 10:05 PM | #25 |
Major General
2374
Rep 8,364
Posts |
|
Appreciate
0
|
05-30-2018, 04:55 AM | #26 |
New Member
6
Rep 20
Posts |
He needs to turn the ignition on, read the ECU(s) (he will see around 17) and then edit fdl. Turn the ignition off and Code FDL. This way he will not have the engine turn off while codes being applied, and will still see the "sleeping" ECU's as per his screen shot above.
__________________
Max Pavlov
|
Appreciate
0
|
05-30-2018, 04:56 AM | #27 |
New Member
6
Rep 20
Posts |
The only really tricky part is to code ACC memory for Eco Pro. Mine still has ASS on every time I switch to Eco Pro, but I remember seeing this setting somewhere.
__________________
Max Pavlov
|
Appreciate
0
|
11-16-2019, 09:07 AM | #28 | |
Major
606
Rep 1,455
Posts |
Quote:
I just turned engine on and then off. Then all ECUs became visible and I could code the stop/start setting in the DME_BAC2 module without problem |
|
Appreciate
0
|
07-02-2020, 10:44 AM | #30 |
Enlisted Member
14
Rep 49
Posts |
|
Appreciate
0
|
10-21-2020, 11:27 AM | #31 |
Registered
0
Rep 2
Posts |
|
Appreciate
0
|
01-31-2022, 03:13 AM | #32 | |
New Member
0
Rep 23
Posts |
Quote:
If you start remotely car by keyfob in comfort mode could you share info. Thanks |
|
Appreciate
0
|
01-15-2023, 02:30 PM | #33 |
New Member
0
Rep 13
Posts |
i´ve coded tcm_msa_memory to wert01 in dme but the memory always turn "off" after turn off ignition. also it dont remember...Any Idea? I-Step is 21-03-520....Ive completly disabled MSA but with 2 engine errors this is stupid :/
|
Appreciate
0
|
01-16-2023, 12:24 AM | #34 | |
Enlisted Member
14
Rep 49
Posts |
Quote:
Did you figure it out? If not then I am sorry to tell you that with the new firmware, your DMEs are now locked and they need to be bench unlocked by a professional tuner shop in order to permit coding again. |
|
Appreciate
0
|
01-16-2023, 12:27 AM | #35 | |
Enlisted Member
14
Rep 49
Posts |
Quote:
? BTW, does your 540i have 1 or 2 DME's |
|
Appreciate
0
|
01-16-2023, 03:26 AM | #36 | |
New Member
0
Rep 13
Posts |
Quote:
And i only have 1 dme. Coding works fine on dme |
|
Appreciate
0
|
01-16-2023, 08:58 AM | #37 |
Enlisted Member
14
Rep 49
Posts |
|
Appreciate
0
|
01-16-2023, 03:44 PM | #38 |
New Member
0
Rep 13
Posts |
I've coded the DME to default. (tcm_msa_memory =wert00) and then Change it again to wert01. After coding its sucessfull set after read the ncd again..... But it doesnt remember my setting
Seems to be I-Step relevant :/ |
Appreciate
0
|
02-02-2023, 05:12 AM | #39 |
Major General
2374
Rep 8,364
Posts |
Never seen an integration level where it could not be coded. Also not sure why you coded it twice.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|