06-09-2022, 10:09 AM | #155 |
Private
36
Rep 94
Posts |
I had similar changes too.
When i bought my car 0km, the car with p7 cinturatos 18inch wheels. The speed area of vibration was 105-120kmh, after that got bridgestone er300 vibration same and speed range is 125-140km/h |
Appreciate
0
|
06-09-2022, 10:21 AM | #156 |
New Member
15
Rep 29
Posts |
I don't believe it has anything to do with tires or wheels. The two 540's I went through had different wheel sizes/wheel designs and different tires. As a matter of fact, the dealer tried different brand tires as well and nothing helped.
|
Appreciate
0
|
06-09-2022, 11:40 AM | #157 |
Private
60
Rep 66
Posts |
Hi,
After few research in german forum, a possible solution : https://www.motor-talk.de/forum/vibr...-t7293197.html https://www.hubauer-shop.de/en/8053074-disc-for-h.html The possible solution is to center perfectly the wheel on the hub and use friction disk between the wheel and the hub ( example in link hubauer shop) regarding to the person who created this post, the friction disk prevent the wheel to move and create vibration |
Appreciate
0
|
06-09-2022, 02:42 PM | #158 | |
Private
36
Rep 94
Posts |
Quote:
The symptopms are very close to mine and i’ll try to find these pieces. Unfortunately its very hard to find these on Turkey Until i find these pieces should i try plastic rim rings like below? It also prevents wheel movements |
|
Appreciate
0
|
06-09-2022, 03:29 PM | #159 | |
Private
60
Rep 66
Posts |
Quote:
I don't recommend to use the plastic rims like below, its not original part, it doesn't fit, and it can make damage. these pieces are BMW original part, it can be possible to order that in you bmw dealer. I have already ordered 2 pieces for the rear wheels, i will report here the conclusions |
|
Appreciate
1
HighlandPete6658.50 |
06-09-2022, 04:16 PM | #160 | |
Private
36
Rep 94
Posts |
Quote:
Okay then, waiting your upgrades. wish this solve our issue |
|
Appreciate
0
|
06-09-2022, 04:20 PM | #161 | |
Lieutenant General
6659
Rep 15,858
Posts |
Quote:
Got to ask, has anyone actually measured the hub spigot and wheel center bore to see what the clearance is? It may be too big a tolerance and allowing an eccentric mount, if extra mounting care is not followed. We've been here before with previous models, if the machining had too wide a tolerance. Many of us know how hub centric rings can be necessary to take up the 'slack' on rims with a larger bore. But we shouldn't have issues with BMW OE mated parts. |
|
Appreciate
0
|
06-09-2022, 04:54 PM | #162 |
Major
330
Rep 1,028
Posts |
Interesting, watching this as a possible solution.
Does anyone have the BMW part numbers for these discs? FYI road force balance should be done with a mount that is through the 5 bolt holes not an inner cone so it negates any non centric issue on the wheel but if the wheel can still move when driving due to mating surface problems that can definitely cause vibrations etc.l but it shouldn't cause wheel hop on hard acceleration. Have any of you checked your transmission mounts with a Borescope I did see attached. Only 36000 Km on the car when I did this and all of them had tears but BMW say it's not an issue. Not sure I believe them any more. A transmission moving too much can cause wheel hop when hard accelerating from what I read online. Also too much movement can cause drive issues which can manifest as what feels like shaking or vibrations. You should also check this, it's very easy to do if you can get under the car and pickup a cheap Borescope I paid only 35 Euro for this one at ALDI. |
Appreciate
0
|
06-09-2022, 06:06 PM | #163 | |
Lieutenant General
6659
Rep 15,858
Posts |
Quote:
You mention the soft bushings, can certainly contribute to wheel hop on hard acceleration. Whether worn out or not may depend on how the tyres grip. I remember my F11 suffering from wheel hop on a couple of occasions, on a specific bit of road under hard acceleration. Tyre treads were getting down, so whether better or worse grip was a contributing factor, not certain. After changing to new tyres, (same brand and spec'), never had it happen again. |
|
Appreciate
0
|
06-10-2022, 04:56 AM | #165 | |
Private
60
Rep 66
Posts |
Quote:
i think that the friction disc prevent the wheel from moving and reach that tolerance. I will try it when i receive the discs. |
|
Appreciate
0
|
06-10-2022, 05:54 AM | #166 |
Major
330
Rep 1,028
Posts |
Hi Pete my tyres are in very good condition plenty of thread MPS3 RFTs.
I'm convinced the power on back left is not being put down properly and it's the drive shaft, transmission or shock causing the issue (maybe top mount). Became much more apparent after remapping the car as it putting down a lot more power. The back left is the corner I've had issue with all along. Who know but it's not that big a deal to do the shock top mount and drive shaft I have the parts but the transmission mounts is a different issue and big work. I find it weird they all have tears so soon but I didn't own the car since new so who knows what happened. Also BMW saying it's no big deal is also worrying how would they know on a car that at time I had issue was only 3.5 years since release I suspect that are talking crap. |
Appreciate
0
|
06-11-2022, 03:27 AM | #167 |
Private
83
Rep 61
Posts
Drives: BMW G30 2018
Join Date: May 2022
Location: Bengaluru
|
Subscribed
|
Appreciate
0
|
06-13-2022, 05:46 AM | #168 | |
Private
36
Rep 94
Posts |
Quote:
Did you get them. Will order according to your feedbacks. Thank you. |
|
Appreciate
0
|
06-13-2022, 08:13 AM | #169 |
Private
36
Rep 94
Posts |
!! update !!
Tesa Rubber tape applied on wheel hub. Vibrations was 10/10 now 2/10 There is 2-3mm movement on wheel hub. I think end of the tunnel is the fritction disk. |
Appreciate
0
|
06-13-2022, 10:52 AM | #170 |
Private
60
Rep 66
Posts |
Good news, my frictions disk are coming this wednesday, and i will try to mount them this week.
|
Appreciate
0
|
06-13-2022, 11:12 AM | #171 |
Private
36
Rep 94
Posts |
|
Appreciate
0
|
06-13-2022, 11:39 AM | #172 | ||
Lieutenant General
6659
Rep 15,858
Posts |
Quote:
BMW Data for my F11; Quote:
I wonder if this is the real issue here, tolerances are far to wide on the G30 builds. |
||
Appreciate
0
|
06-14-2022, 07:55 AM | #174 |
Lieutenant
325
Rep 436
Posts |
I’m very much thinking the same, if that ‘tape’ is re-centring the wheel around one axis, then what is happening to the stud pattern and torque settings, something will be way out at 2-3 mm thickness.
|
Appreciate
0
|
06-14-2022, 01:03 PM | #175 | |
Private
60
Rep 66
Posts |
Quote:
it's the job of the grip contact zone between the wheel and hub. |
|
Appreciate
0
|
06-14-2022, 01:10 PM | #176 | |
Major General
4484
Rep 5,366
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|