[kubax86]

Originally Posted by bliznaka87

Hello friend, i have g30 with kafas4 and need 11f fsc for my vin,i have activated it with esys and now need only fsc, i see that you have imported and activated it for your car can you help? Thanks!

PM sent

[Iron-nerve]

Originally Posted by kubax86

From now on, we have an option to activate SLI on all 2021/2022 cars included newest from dealers

Interested mate, please advise how it works and what do you require off me, is it applicable to all cars with new type of camera in Windscreen?


Thanks

[kubax86]

Originally Posted by Iron-nerve

Interested mate, please advise how it works and what do you require off me, is it applicable to all cars with new type of camera in Windscreen?


Thanks

PM sent

[Laurentvh]

kubax86

Could you sent me PM as well for SLI coding on 2021 G30 please?
iDrive7 with latest KAFAS4.

[kubax86]

Originally Posted by Laurentvh

kubax86

Could you sent me PM as well for SLI coding on 2021 G30 please?
iDrive7 with latest KAFAS4.

Yes, PM sent

[Biliardiere]

Originally Posted by Fari84

I have fdl coded HU, Kombi and Kafas, with this parameters:


(HU
SPEEDLIMIT_INFO: aktiv [01]

KAFAS
NPI_ENABLE: initwert [01]
SLI_ENABLE: initwert [01]

KOMBI
CB_TACHOZEIGERBAND: aktiv [01]
HUD_NO_PASSING_ENABLE: aktiv [01]
HUD_SPEED_LIMIT_ENABLE: aktiv [01]
NO_PASSING_ENABLE: aktiv [01]
PIA_HUD_SLI: aktiv [01]
PIA_HUD_SLI_NPI: aktiv [01]
PIA_HUD_SLI_PORTIERUNG: aktiv [01]
PIA_HUD_VSLI: aktiv [01]
PIA_SLI_NPI: aktiv [01]
PIA_TACHOZEIGERBAND: aktiv [01]
PIA_TACHOZEIGERBAND_PORTIERUNG: aktiv [01]
RCOG_TRSG_APPL: aktiv [01]
RCOG_TRSG_TIMEOUT: aktiv [01]
SPEED_LIMIT_ENABLE: sli [01]
TACHOZEIGERBAND_ENABLE: aktiv [01]
SLI_PERMANENT_ENABLE: aktiv [00]
ADDITIONAL_SIGN_ENABLE: aktiv [00])

I also don´t know why i don´t find this parameter:

"SLI_PERMANENT_ENABLE: aktiv [00]"

Thanks

if my car does not have a HUD, do I have to encode the strings with the word hud from this list? Thank you

[kubax86]

Originally Posted by Biliardiere

if my car does not have a HUD, do I have to encode the strings with the word hud from this list? Thank you

No need

[Biliardiere]

Originally Posted by kubax86

No need

for BMW software recall all the control units have been reset and I have lost all the codings made .. SLI, CarPlay in full screen and etc.
I have encoded everything except SLI, the question is: is original FSC always loaded in Kafas? Just encode the parameters in the list and then SLI works?
Thanks Kubax86

[kubax86]

Originally Posted by Biliardiere

for BMW software recall all the control units have been reset and I have lost all the codings made .. SLI, CarPlay in full screen and etc.
I have encoded everything except SLI, the question is: is original FSC always loaded in Kafas? Just encode the parameters in the list and then SLI works?
Thanks Kubax86

Correct

[Biliardiere]

Originally Posted by kubax86

Correct

ok everything works great.
Thanks Kubax

[Laurentvh]

Originally Posted by kubax86

Yes, PM sent

Coded SLI on new G30 LCI today, great job! kubax86

[rvkrn]

Hi Everyone,


I'm new here and a new owner of a 520i, i'm looking to code SLI and i need help with 11F FSC Code for Speed Limit Info (SLI) and to code it. can someone help please?

Where is the best place to get FSC code?

[kubax86]

Originally Posted by rvkrn

Hi Everyone,


I'm new here and a new owner of a 520i, i'm looking to code SLI and i need help with 11F FSC Code for Speed Limit Info (SLI) and to code it. can someone help please?

Where is the best place to get FSC code?

PM sent

[beanbaguk]

I just want to give a big shout-out to kubax86 from Bimmer Remote Coding (https://bimmer-remote.com), for coding the SLI FSA to my car just now.

The whole thing took about 15 minutes from start to finish and it was by far one of the better prices I found when doing my search. (Bear in mind while there are cheaper options on eBay, you need to consider the reputation of the coder. After all, you are allowing an unknown person to tap into your very expensive investment!!!)

All in all, I'd highly recommend this fella. Sorted everything out on Facebook Messenger, connected up the laptop, ENET cable and installed TeamViewer 14. (Make sure you install the VPN driver too).

I just gave the TV ID to kubax86 and less than 15 minutes later, it was all done.

Thank you again.

[cbadea]

Originally Posted by Laurentvh

I also got reply from the guys in the Netherlands (NDH)
https://ndh.nu/?product=bmw-speed-limit-info-activatie

For G30 LCI (2021 models) it doesn't seem possible yet to code, as BMW is not yet giving the FSC code for the newer models (with latest KAFAS camera)
I've agreed to contact them again in 3months to see if there are any updates by then.

Hey,

Have you managed to sort this out? Someone just did it for me as I'm very newbie when comes esys/coding.

Cristian

[maximal]

Hello,

I would like to know how to activate SLI. I have BimmerCode and wifi adapter.

[Wojti_]

Originally Posted by maximal

Hello,

I would like to know how to activate SLI. I have BimmerCode and wifi adapter.

need code car and loadd SLI certificate
PM sent

[kubax86]

Originally Posted by maximal

Hello,

I would like to know how to activate SLI. I have BimmerCode and wifi adapter.

PM sent

[WretchedRefuse]

Please send info on how to obtain the FSC and activate SLI. I have a 2020 M550i. Thanks!

[RedJack]

Hello!
I also want to install SLI on G30 2019.
Can someone tell me the source of trust in the FSC Cafas4 code here?
Thank you

[Wojti_]

Originally Posted by RedJack

Hello!
I also want to install SLI on G30 2019.
Can someone tell me the source of trust in the FSC Cafas4 code here?
Thank you

I can help with fsc and coding remotely

[Wojti_]

Originally Posted by WretchedRefuse

Please send info on how to obtain the FSC and activate SLI. I have a 2020 M550i. Thanks!

I can help with fsc and codind remotely