12-24-2017, 04:59 PM | #1 |
Private
9
Rep 68
Posts |
Voice Command stopped working, after coding.
I bought a V-Link dongle and Bimmercode.
I have followed some of the steps for coding in EBT, and the popular features. Which have all mostly worked! So that’s for peoples input. I have however lost my Voice Command on the steering wheel, I think when I coded in Office. I have checked the CE Device Speech Recognition is “active” Any ideas? |
02-04-2018, 03:49 PM | #3 |
Private
9
Rep 68
Posts |
I haven't no.
I did send an message to the support team of Bimmercode, but they said that there not sure which setting has caused this. I did do some searching and looked at the settings and mine as all active, so unsure! Thanks Luke |
Appreciate
0
|
02-04-2018, 03:53 PM | #4 |
New Member
4
Rep 25
Posts |
I have contacted Stephan from bimmercode same result.
Have found 2 option that should be active, changed them... Still dosn't work. I think ill have to change to stock (dont know yet how) and do it again by esys... |
Appreciate
0
|
02-23-2021, 06:00 AM | #6 |
Registered
0
Rep 4
Posts |
Hi I have the same problem I've reset the module but with no joy and bimmercode support are as much use as a chocolate tea pot.
There reply was well if you have done a reset and it's still not working its not the programming look on the Internet for a solution. There is obviously a problem with the coding as there are quite a few people with the same issue after programming with bimmercode. |
Appreciate
0
|
02-23-2021, 05:26 PM | #7 |
Brigadier General
1646
Rep 4,877
Posts |
Ok, I've never used Bimmercode to code my car, but here is the notes I took off the forum when I used ISTA to code office into my car. I'd check if they are all "acktiv" after Bimmercode.
SINGLE_OR_MULTILINK werte = 01 Rest all aktiv: CONTACT_BOOK_PICTURES BLUETOOTH_2ND_HFP MACRO_PIM PIM_SPEECH_TO_TEXT PIM_NEW_ELEMENT_VOICE_EMAIL PIM_BILDER_EIN_AUS CALENDAR_EIN_AUS TASK_EIN_AUS REMINDER_EIN_AUS TEXT_NOTES_EIN_AUS AUDIO_NOTES_EIN_AUS SMS_EIN_AUS EMAIL_EIN_AUS PIM_NEW_ELEMENT_EMAIL PIM_NEW_ELEMENT_SMS PIM_NEW_ELEMENT_AUDIO_NOTE |
Appreciate
0
|
03-02-2021, 05:39 AM | #8 |
Registered
0
Rep 4
Posts |
I had the same issue when following instructions to code EBT on here. I got over it by changing the following two which were shown as nicht_aktiv in the instruction i followed (as below) to Aktiv.
HU_NBT > HMI 3000 > SVS = nicht_aktiv [Default] HU_NBT > HMI 3000 > SYSTEM_TTS = nicht_aktiv [Default] I also had CE Speech Recognition as Aktiv. Hope this helps. |
Appreciate
0
|
03-18-2021, 07:30 AM | #9 |
Registered
0
Rep 4
Posts |
Thanks for the help I tried the larger settings but no change, when I changed SVS to aktiv i now get voice will be available shortly but does not start
any other ideas? Thanks |
Appreciate
0
|
08-06-2021, 02:45 AM | #10 |
Enlisted Member
6
Rep 36
Posts |
|
Appreciate
0
|
08-21-2021, 08:35 AM | #11 | |
Registered
0
Rep 1
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|