Error code, any idea's?

RichRoberts44 · 12-02-2019, 10:56 AM

Hi all,

Very recently got error code CC-ID 132. Looking at previous posts this points to angel eye bulbs. Here's where it gets a bit complicated.

I bought some LCI angel eye halogen lights to replace my pre LCI non angel eye lights. I wired in some LED halo's into the headlight, swapped the pins around so they work as sidelights and never got round to programming them in to work as DRL's. This was 7 months ago and its been absolutely fine until the temperature dropped. Any idea's? All lights are working as they have been. Is this going to be a voltage issue? Any way around it?

Thanks

iqraceworks · 12-02-2019, 10:59 AM

I would go back through and check all of your wiring changes you made.

RichRoberts44 · 12-02-2019, 12:38 PM

Even though its been working for a long time and still is working? I had some condensation and left 1 of the rear covers off for a week to clear it, could this have caused it in the cold? Corrosion maybe?

iqraceworks · 12-02-2019, 01:00 PM

Quote:

Originally Posted by RichRoberts44

Even though its been working for a long time and still is working? I had some condensation and left 1 of the rear covers off for a week to clear it, could this have caused it in the cold? Corrosion maybe?

That's a good place to start......

gbalthrop · 12-02-2019, 02:07 PM

Quote:

Originally Posted by RichRoberts44

...Very recently got error code CC-ID 132...I bought some LCI angel eye halogen lights to replace my pre LCI non angel eye lights. I wired in some LED halo's into the headlight, swapped the pins around so they work as sidelights and never got round to programming them in to work as DRL's. This was 7 months ago and its been absolutely fine until the temperature dropped...

As you probably know, CC-ID indicates bulb failure in Right-Front Side Light. I presume you have Bulb Fail warning light on instrument cluster?

Since you had nearly 7 months of NO Bulb Fail use since your wiring changes, and the "Bulb Fail" is ONLY on the Right Side, it seems more likely that you have a ground, wiring or Connector issue than an issue related to the LED installation 7 months ago.

Here is the TIS circuit diagram for Side Lights for models built BEFORE 8/2008:
https://www.newtis.info/tisv2/a/en/e...lights/i7o2pTr

George

12-02-2019, 10:56 AM	#1
RichRoberts44 New Member 0 Rep 13 Posts Drives: 320D TOURING M SPORT Join Date: Aug 2018 Location: Worcs iTrader: (0)	Error code, any idea's? Hi all, Very recently got error code CC-ID 132. Looking at previous posts this points to angel eye bulbs. Here's where it gets a bit complicated. I bought some LCI angel eye halogen lights to replace my pre LCI non angel eye lights. I wired in some LED halo's into the headlight, swapped the pins around so they work as sidelights and never got round to programming them in to work as DRL's. This was 7 months ago and its been absolutely fine until the temperature dropped. Any idea's? All lights are working as they have been. Is this going to be a voltage issue? Any way around it? Thanks
	Appreciate 0 Tweet Quote

12-02-2019, 10:59 AM	#2
iqraceworks Brigadier General 2001 Rep 3,731 Posts Drives: 2007 335i Join Date: Aug 2019 Location: Missouri iTrader: (0)	I would go back through and check all of your wiring changes you made.
	Appreciate 0 Quote

12-02-2019, 12:38 PM	#3
RichRoberts44 New Member 0 Rep 13 Posts Drives: 320D TOURING M SPORT Join Date: Aug 2018 Location: Worcs iTrader: (0)	Even though its been working for a long time and still is working? I had some condensation and left 1 of the rear covers off for a week to clear it, could this have caused it in the cold? Corrosion maybe?
	Appreciate 0 Quote