|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Help!! e90 335i trippin out
|
|
06-10-2012, 06:22 PM | #1 |
Banned
25
Rep 386
Posts |
Help!! e90 335i trippin out
hey guys i reset air control, throttle valve adapt,fuel/ air adapt/ secondary air injection with the bt tool and when i started my car it kept revving and i turned it off immediatly gave my a dtc malfunction... i set map 0 on jb4 before doing this... PLEASE HELP dont know what to do next...
|
06-10-2012, 06:37 PM | #2 |
Banned
25
Rep 386
Posts |
lol the e90 has one sketchy computer after 2 restarts with the car erractically revving and giving me every error code thinkable i start it up the third time and it starts perfectly. drove it feels fine..????? no fault codes either wtf
|
Appreciate
0
|
06-10-2012, 07:15 PM | #3 | |
Lieutenant
71
Rep 510
Posts |
Quote:
__________________
'2018 F87 M2 LCI | LBB | GC Camber Plates | Ohlins R&T 90/190N/mm | 18x10 et33 square 275/35 | MPe | Poly Transmission Mounts | Recaro Sportster CS
|
|
Appreciate
0
|
06-10-2012, 08:51 PM | #5 |
Lieutenant
19
Rep 569
Posts |
I had something similar, but the car never ran quite right. I pulled out the JB4 and then reinstalled it and never had the problem again.
Maybe I had a loose wire or bad connection somewhere. |
Appreciate
0
|
06-10-2012, 10:17 PM | #6 |
Banned
25
Rep 386
Posts |
|
Appreciate
0
|
06-10-2012, 11:23 PM | #7 |
Banned
52
Rep 1,497
Posts |
|
Appreciate
0
|
06-11-2012, 11:38 AM | #8 |
Lieutenant
15
Rep 447
Posts |
it happened sometimes when you do throttle adaptation reset its common at least for me whenever i upload new maps and firmware it's go apeshit on restart power off reset adaptation agains and comes back on fine no issues.
|
Appreciate
0
|
06-11-2012, 11:40 AM | #9 | |
Banned
25
Rep 386
Posts |
Quote:
|
|
Appreciate
0
|
06-11-2012, 12:26 PM | #10 |
Private First Class
11
Rep 160
Posts
Drives: 2007 335i coupe
Join Date: Feb 2010
Location: Grand Rapids, MI
|
I have had this problem when I reset my adaptions and did not reset the ECU last. It can be fixed by resetting the ECU, not just turning the ignition off.
|
Appreciate
0
|
07-05-2012, 12:36 AM | #11 |
Registered
0
Rep 2
Posts |
I may be a fool...
The same thing has just happened to my car after adaptation reset...
Not sure how to reset ECU so I had to pull the battery cable for 5 minutes, then performed a throttle switch reset. This seems to work for me to restore normalcy. Hopefully this information is helpful for somebody who panicking as much as I was. |
Appreciate
0
|
07-05-2012, 09:45 AM | #12 |
Major
36
Rep 1,054
Posts |
This happens often during resets. You will thorugh Trans codes, use BT to clear. If you do throttle valve adaptions, the car will hicc-up with throttle angles unless its done correctly. There is a thread on how to do it properly in this fourm.
__________________
JB4 beta 15 ohms FSB,AEM inline filter/ CM 10, ETS fmic, ER custom made charge pipe,TSW Donnington 18's,Simitumo HTRZ3, Injen DCI, AR DPs, Forge DVs, AA SLD, Koni FSD, ZSP springs.
|
Appreciate
0
|
Bookmarks |
|
|